Checking and design of a reinforced concrete section in simple bending, to EN 1992-1-1 and, for road bridges, EN 1992-2, with their French National Annexes.

The sheet applies the French National Annexes: its interface and the PDF calculation note are in French.

How to use

  • Describe the section (rectangular, T, L or any polygon), the materials, then the reinforcement layers: up to eight layers, at the bottom face, the top face or an intermediate level.
  • Enter the design moments: ULS, characteristic, quasi-permanent and, for a bridge, frequent SLS; for fatigue, the moments under fatigue load model FLM3.
  • “Calculer” gives the verdict and the utilisation ratio of each criterion; when the section fails, quantified suggestions (reinforcement, depth, concrete class).
  • The PDF calculation note, in THEOREMS colours, can be downloaded below the results: assumptions, detailed calculations and summary of checks.

Assumptions

  • Ultimate limit state: section equilibrium with strain limits (§6.1), parabola-rectangle or rectangular stress block, steel with horizontal or inclined top branch; γc = 1.5, γs = 1.15, Es = 200,000 MPa.
  • Serviceability: transformed section, cracked beyond the cracking moment; effective concrete modulus under quasi-permanent loads, non-linear creep beyond 0.45 fck (§7.2(3)); stress limitation according to the exposure class (§7.2).
  • Cracking: direct crack width calculation (§7.3.4) or the EC2-2 National Annex rule (§7.3.3(101)); frequent combination for road bridges, quasi-permanent for buildings.
  • Fatigue of reinforcement in road bridges: exemption if σs ≤ 300 MPa under the characteristic combination (§6.8.1(102)), otherwise damage equivalent stress range method of Annex NN.
  • Simple bending only: no axial force, shear or torsion; detailing rules remain to be checked.

Example

Road bridge deck slab, 25 cm thick, per 1 m strip: C30/37 concrete, 10 HA16 bars (d = 199 mm), MEd = 110 kN·m; fatigue under load model FLM3.

✔ Section verified

Maximum utilisation ratio: 0.88 — governing criterion: reinforcement fatigue (exempt if σs,char < 300 MPa)

MRd
154.3 kN·m
As provided
2,011 mm²
As required
1,375 mm²
wk
0.216 mm

Ample resistance (ratio 0.71), cracks at 0.216 mm against 0.30 mm. The sheet also flags concrete fatigue, not exempt (18.06 MPa against 0.6·fck = 18 MPa), and quantifies two remedies: C35/45 or h = 260 mm.

Load this example into the sheet Calculation note of the example (PDF, 5 pages, in French)

SLS neutral axis1000 mm250 mm
Example section, to scale: 10 HA16 bars per metre; dashed, the SLS neutral axis (quasi-permanent combination, y = 89.6 mm).
Formulas, limits and references

μ = MEd/(b·d²·fcd) ≤ μlim = 0.372; As = MEd/(z·fyd)
wk = sr,max·(εsm − εcm)

Limits

  • Simple bending only: no axial force, shear, torsion or prestressing.
  • Buildings and road bridges; railway bridges are not covered.
  • Not covered: deflections, detailing, fire, seismic design; concrete fatigue flagged, not calculated.

References: EN 1992-1-1 and EN 1992-2 with their French National Annexes; EN 1990 (Annex A2); EN 1991-2 (FLM3, §4.6.4); our course Actions, limit states and combinations.

Check: example checked by hand (μ, z, As, sr,max, wk).

Frequently asked questions

Why several service moments?

Each check has its own combination: characteristic for stresses and the fatigue exemption, quasi-permanent for creep (and cracking in a building), frequent for cracking in a road bridge.

Direct calculation of wk or National Annex rule?

The direct calculation (§7.3.4) is the reference method; for bridges, the French annex to EC2-2 also accepts the rule of §7.3.3(101). The sheet applies the chosen method and gives the other for information.

How do I handle a T section or a special shape?

Choose “T” or “L” and enter the effective flange width beff (§5.3.2.1); for a slab with cantilevers or a bulb-tee beam, describe the outline by its vertices.

See also

Sheets for preliminary design and routine checks, provided for guidance only: they do not replace a calculation note prepared by an engineer. Found an issue or have a suggestion? Write to us.