Common load cases for beams, frames, arches and rings, with their diagrams and the formulas for support reactions, internal forces, deflections and rotations, section properties, buckling and torsion, together with general calculation methods. Straight beam cases open in the beam calculator and sections in the Section properties tool, already set up, to obtain numerical values.
- Statically determinate beamsSimply supported beams, cantilevers, overhangs and inclined beams. 19 cases.
- Statically indeterminate and continuous beamsFixed–pinned and fixed–fixed beams, and continuous beams with two to four spans. 19 cases.
- Thermal gradient and variable inertiaEffects of a temperature difference between the faces of a beam, beams with stepped inertia. 7 cases.
- Frames, arches and ringsSingle-bay portal frames with pinned or fixed bases, three-hinged, two-hinged and fixed parabolic arches, thin circular rings. 15 cases.
- Sections, buckling and torsionGeometric properties of common sections, shear stresses, Euler critical loads and torsion of solid, open and closed sections. 15 cases.
- PlatesKirchhoff thin plates: equations, Wood-Armer moments, circular and rectangular plates, load spreading and wheel loads on slabs. 13 cases.
Notation and conventions
- L: span; a, b: distances from a load to supports A and B (a + b = L); c: overhang length; h: height of a frame or depth of the section; f: rise of an arch; R: radius of a ring.
- q: distributed load (kN/m); P, F: point loads (kN); C: applied moment (kN·m); p: pressure (kN/m); ΔT: temperature difference between the faces (K); α: coefficient of thermal expansion.
- E: elastic modulus; I: second moment of area of the section; A: area; EI constant unless stated otherwise.
- Straight beams: reactions positive upwards; bending moment positive when the bottom fibre is in tension; deflections positive downwards; rotations positive clockwise. Frames, arches and rings: the fibre in tension is stated explicitly.
- Linear elasticity, small displacements, shear deformation neglected (Euler-Bernoulli theory); axial force has no effect on bending (no second-order effects).
General relationships
| Equilibrium of a beam element | |
|---|---|
| Elastic curve equation | (w: deflection, positive downwards) |
| Bending stress | (v: distance from the neutral axis) |
| Shear stress | (S: first moment of area of the part beyond the fibre considered; b: width at that level) |
Three-moment equation (Clapeyron)
For a continuous beam with constant EI under uniform loads (qi on span i, of length Li), the support moments Mi−1, Mi, Mi+1 of two consecutive spans satisfy:
One equation per intermediate support, with M = 0 at simply supported end supports: the system gives the support moments, then each span is treated as a simply supported beam under its own load and end moments.
Mohr integrals
To calculate a deflection or rotation by the virtual work method, , where M is the moment due to the actual load and m the moment due to a unit load applied at the point and in the direction considered. Over a length L with constant EI:
| Diagrams | ∫ M m dx |
|---|---|
| Rectangle M × rectangle m | |
| Rectangle M × triangle m | |
| Triangle M × triangle m, peaks on the same side | |
| Triangle M × triangle m, peaks on opposite sides | |
| Parabola M (uniform load, maximum at midspan) × rectangle m | |
| Parabola M × triangle m | |
| Parabola M × parabola m | |
| Trapezium M (M₁, M₂) × trapezium m (m₁, m₂) | |
| Trapezium M (M₁, M₂) × parabola m |
Sources and checks
Classical strength of materials formulas, obtained by integrating the elastic curve equation, the force method or energy theorems. Every formula in this handbook is checked numerically on an example, against the THEOREMS beam calculator or, for frames, arches, rings and inclined beams, against a plane frame finite element analysis, and for sections against the Section properties tool; buckling lengths and torsion coefficients are recalculated numerically: the difference is below 0.5%.
Preliminary design aids, provided for guidance only: they do not replace calculations prepared by an engineer. Found an error, have a suggestion? Write to us.